All Categories

Focusing on the R&D and production of duct and tube cleaning machines since 2009

News

Home >  News

KT-965A CCTV Pipeline Inspection Robot: Parameters, Functions, and Application Scope

Time : 2026-11-20 Hits : 0

1. What Robot Is Used for DN260–DN2000 Pipeline Inspection? How Does the KT-965A Address Wide-Range Pipe Diameter Inspection Requirements?

If the pipelines to be inspected include both small-to-medium diameters around DN260 and municipal main pipelines or large box culverts above DN1000, equipment selection must consider crawler dimensions, wheel set adaptability, camera height, and the internal observation range of the pipeline.

The KT-965A CCTV Pipeline Inspection Robot is a CCTV crawler robot designed for inspection of small-to-medium pipelines through large pipelines, box culverts, and underground pipeline networks. The product is applicable to pipe diameters of DN260–DN2000 mm. It uses dual-motor four-wheel drive, front and rear dual cameras, a 720° surround-scanning gimbal, and an X-shaped electric lifting frame. The standard configuration includes a 100 m cable, customizable up to 500 m.

Compared with inspection methods relying only on a single front camera, the KT-965A uses front and rear dual cameras and multi-directional gimbal observation to assist with forward-direction observation, return inspection, and multi-angle pipe wall image acquisition. The electric lifting mechanism is used to adjust camera height and, together with 5-inch and 8-inch rubber wheel sets, adapts to observation requirements in pipelines of different sizes.

For municipal drainage network inspection units, third-party inspection agencies, pipeline maintenance enterprises, trenchless rehabilitation construction units, and engineering units responsible for underground utility tunnel operation and maintenance, the KT-965A can serve as a CCTV inspection equipment selection option for main pipeline networks.

ScreenShot_2026-11-20_104910_647.jpg


2. What Are the Main Functions of the KT-965A CCTV Pipeline Inspection Robot?

2.1 DN260–DN2000 Pipe Diameter Adaptability with Electric Lifting for Camera Height Adjustment

The KT-965A crawler uses an X-shaped electric lifting structure with a lifting height of 120 mm.

Retracted dimensions: 750×130×180 mm

Raised dimensions: 750×130×300 mm

Equipped with 5-inch and 8-inch rubber wheel sets, four of each

Product applicable pipe diameter: DN260–DN2000 mm

The internal space of pipelines varies significantly with different pipe diameters. If the camera position is too low, a suitable pipe wall observation angle may not be obtained. If the position is too high, observation of the pipeline bottom and side walls may also be affected.

The electric lifting structure can adjust vehicle body height based on pipe diameter and site conditions, keeping the lens as close as possible to a suitable observation position.

Note: The marked DN260–DN2000 applicable range does not mean the equipment can directly enter under any pipeline conditions. Actual passage also requires consideration of effective inner diameter, pipeline deformation, sediment height, bend configuration, and wheel set configuration.

2.2 Dual-Motor Four-Wheel Drive with In-Place Turning

The KT-965A uses dual-motor four-wheel drive, with a maximum output power of 200W. It supports three-speed adjustment and a maximum travel speed of 10 m/min.

Main motion performance includes:

Forward and reverse control

Forward and reverse constant-speed cruise

Three-speed adjustment

Maximum climbing angle of 45°

360° in-place turning

The in-place turning function helps the robot change direction within pipe sections that meet space conditions, reducing repeated reversing operations in some narrow pipe sections.

45° is the maximum climbing angle in product documentation. Actual passage capability is also affected by pipe bottom friction, water accumulation, mud, slope length, obstacles, cable drag, and other factors.

2.3 Front and Rear Dual Cameras for Both Forward and Return Observation

The KT-965A is equipped with two camera systems:

Camera System

Parameters and Functions

Front camera

2.1 megapixels, 1920×1080

Rear camera

5-megapixel starlight HD camera

Optical zoom

10×

Digital zoom

16×

Minimum illumination

0.001 lux

Photo capture during video recording

Supported

The front camera is mainly responsible for forward-direction observation, while the rear camera is used for reverse observation and return inspection.

For longer pipe sections, front and rear dual cameras can provide images from different directions. Inspection personnel can switch cameras based on site conditions, reducing the viewing limitations of relying on only one direction.

2.4 720° Surround-Scanning Gimbal for Multi-Angle Internal Pipeline Observation

The KT-965A gimbal has an axial rotation range of 360° and a pitch range of 180°, and supports auto focus.

The product's so-called 720° surround scanning is achieved through the combined movement of the lens and gimbal to enable multi-directional observation. Inspection personnel can adjust the lens angle to observe the pipeline top, side walls, bottom, and suspected defect areas.

When inspecting visible problems such as cracks, abnormal joints, corrosion, and foreign objects, the observation angle can be adjusted via the gimbal and then combined with optical zoom for detail verification.

Note: 720° surround scanning does not mean that a single pass automatically guarantees no blind spots across the entire pipe wall. For suspected defects requiring interpretation, the robot should stop and adjust the lens to obtain clear and complete images.

2.5 Starlight-Level Camera, 13 LED Lights, and One-Key Defogging

Underground pipelines usually have no natural light source, and insufficient light affects image details.

The KT-965A uses a starlight-level camera system with a product minimum illumination of 0.001 lux and is equipped with 13 LED lights:

Far light: 8×5W

Near light: 4×5W

Tail light: 1×5W

Lighting brightness is adjustable, allowing selection of a suitable lighting state based on pipe diameter, observation distance, and in-pipe environment.

The camera is equipped with electric wire heating one-key defogging. The camera operating temperature is -30°C to 60°C. For humid environments and pipe sections with large temperature differences, the defogging function helps maintain clear lens images.

2.6 100 m Standard Cable, Customizable Up to 500 m

The KT-965A cable reel comes standard with a 100 m Kevlar dual-core cable, customizable up to 500 m.

Main parameters:

Cable diameter: 6.5 mm

Cable material: Kevlar dual-core

Pay-out/take-up method: electric/manual

Cable spooling method: automatic spooling

Cable protection: tension buffer protection

Metering system accuracy: ±0.01 m

Long-distance cables are suitable for inspection tasks requiring coverage of longer pipe sections. Tension buffering and automatic cable spooling help manage cable pay-out and take-up, reducing cable accumulation and abnormal pulling.

The metering system can record cable pay-out distance and provide reference for defect location recording. Note that ±0.01 m is the accuracy of the metering system and does not mean that the actual defect coordinate positioning error inside the pipeline is necessarily only 1 cm.


3. KT-965A Tablet Control System and Inspection Report Functions

The KT-965A uses a wireless tablet control terminal equipped with an 11.4-inch 2.4K HD IPS screen, Android system, 6 GB RAM, 128 GB storage, and GPS function.

The tablet can perform equipment operation, image acquisition, parameter setting, and report organization.

Equipment control: Forward, reverse, speed adjustment, gimbal control, lifting control, and gimbal reset.

Image management: Front/rear camera switching, video recording, photo capture, snapshot during video recording, and data storage.

Parameter display: Information such as inclination, air pressure, distance, speed, time, temperature, and battery level.

Auxiliary settings: Metering reset, lighting brightness, attitude calibration, text watermark, and alarm threshold settings.

Report management: Equipped with a self-developed host computer system and municipal underground pipeline defect interpretation software, supporting defect analysis, image organization, and one-click inspection report generation. Report templates can be set according to customer requirements.

Product documentation lists a real-time gas monitoring function. During actual use, the sensor type, gas types detected, measurement range, and alarm conditions in the delivered configuration should be confirmed. This function cannot replace professional gas detection, continuous monitoring, ventilation, and work permit management before confined space operations.


4. Which Customers and Application Scenarios Is the KT-965A Suitable For?

4.1 Municipal Drainage Network Inspection and Maintenance Units

Suitable for internal inspection of rainwater pipes, sewage pipes, and municipal main pipeline networks, and can be used for routine patrol inspection, network census, pre-flood inspection, and inspection before and after maintenance.

Front and rear dual cameras, gimbal, and metering functions help record internal pipeline images and abnormal locations.

4.2 Large Box Culvert and Tunnel Culvert Operation and Maintenance Units

For large box culverts, tunnel drainage systems, and underground passages, the equipment can adjust observation height through electric lifting and different wheel sets, and inspect pipe walls and internal structures with the gimbal.

Actual application requires confirmation of cross-section dimensions, bottom sediment, water depth, and obstacles.

4.3 Third-Party Inspection Agencies

Third-party inspection agencies usually need to complete image acquisition, defect recording, data organization, and report delivery.

The KT-965A supports video recording, snapshot, metering, defect analysis, and report generation, and can be used to assist data acquisition and documentation for inspection projects.

4.4 Trenchless Rehabilitation Construction Units

Before pipeline rehabilitation, CCTV inspection can be used to understand visible internal pipeline conditions and provide image reference for rehabilitation plan development. After rehabilitation is completed, inspection can be performed again to record the internal condition of the repaired section.

The KT-965A itself is pipeline inspection equipment and does not perform dredging, cutting, or trenchless rehabilitation construction functions.

4.5 Power Utility Tunnel, Mine, and Utility Tunnel Operation and Maintenance Units

Can be used for inspection of underground drainage pipes and related passages that meet equipment entry conditions. Before specific use, applicability must be confirmed based on on-site gas environment, protection requirements, communication conditions, and operation management regulations.


5. KT-965A CCTV Pipeline Inspection Robot Technical Parameter Table

Parameter Item

Technical Data

Model

KT-965A

Product Name

CCTV Pipeline Inspection Robot

Applicable Pipe Diameter

DN260–DN2000 mm

System Composition

Crawler, cable reel, wireless tablet control terminal

Drive Method

Dual-motor four-wheel drive

Steering Method

In-place turning

Maximum Output Power

200W

Maximum Climbing Angle

45°

Travel Speed

Three-speed adjustment, maximum 10 m/min

Constant-Speed Cruise

Forward and reverse constant-speed cruise

Protection Rating

IP68

Crawler Operating Temperature

-20°C to 55°C

Crawler Weight

14 kg

Retracted Dimensions

750×130×180 mm

Raised Dimensions

750×130×300 mm

Lifting Height

120 mm

Wheel Sets

5-inch and 8-inch rubber wheels, four of each

Front Camera

2.1 megapixels, 1920×1080

Rear Camera

5-megapixel starlight HD

Optical Zoom

10×

Digital Zoom

16×

Gimbal Rotation

Axial 360°, pitch 180°

Minimum Illumination

0.001 lux

LED Lighting

Far light 8×5W, near light 4×5W, tail light 1×5W

Defogging Function

Electric wire heating, one-key defogging

Camera Operating Temperature

-30°C to 60°C

Standard Cable Length

100 m

Maximum Customized Cable Length

500 m

Cable Diameter

6.5 mm

Cable Type

Kevlar dual-core cable

Metering Accuracy

±0.01 m

Pay-Out/Take-Up

Electric/manual, automatic spooling

Battery Capacity

12.8 Ah

System Voltage

72V

Tablet Screen

11.4 inches, 2408×1720

Tablet RAM/Storage

6 GB/128 GB

Operating System

Android

Optional Functions

Laser width/distance measurement, sonar, LiDAR

Note: The above are product documentation parameters. Specific configuration is subject to the actual contract and delivery list.


6. What Configurations Should Customers Confirm Before Purchasing the KT-965A?

To avoid situations such as pipe diameter mismatch, insufficient cable length, or optional functions not meeting project requirements after equipment delivery, the following items should be confirmed before procurement.

6.1 Inspection Pipe Diameter

Provide the minimum and maximum pipe diameters, as well as the actual effective inner diameter of the pipeline. For pipe sections with deformation, sediment, or obstacles, on-site conditions should be provided.

6.2 Inspection Distance

Confirm the length of each pipe section, manhole spacing, and equipment layout position. Whether the standard 100 m cable is sufficient should be calculated based on actual distance. For long-distance projects, the 500 m customization option can be discussed.

6.3 Internal Pipeline Environment

Confirm whether there is water accumulation, mud, high-flow water, obstacles, and local steps inside the pipe. These factors affect robot passage and camera observation performance.

6.4 Wheel Set and Lifting Configuration

Confirm the combination of 5-inch and 8-inch wheel sets based on pipe diameter range and pipeline bottom conditions, and whether frequent lifting height adjustment is required.

6.5 Inspection Objectives

If the main task is inspection of internal structural defects in pipelines, focus on image quality, gimbal angle, lighting, and report management. If underwater cross-section or pipeline deformation information is required, further confirm whether optional systems such as sonar, laser width measurement, or LiDAR are needed.

6.6 Report and Data Formats

Confirm in advance whether the project has specified report templates, defect record formats, video formats, and data archiving requirements, to avoid mismatch between equipment functions and project delivery requirements.


7. KT-965A Protection Capability and On-Site Usage Precautions

The KT-965A crawler has an IP68 protection rating and is marked with an applicable water depth of 10 m and waterproof pressure of 2.5 bar.

These parameters provide reference for equipment protection capability, but actual use must still be based on the sealing test conditions of the complete machine, connectors, and cables, as well as the product manual. Long-term immersion, flowing water environments, and special medium environments require advance verification.

In addition, the 45° climbing capability is a maximum value and cannot be understood as meaning all 45° slopes can be passed stably. Pipe bottom friction, mud, obstacles, and cable resistance all affect actual performance.

CCTV inspection mainly observes the internal pipeline surface visible to the camera. It cannot directly measure pipe wall thickness, nor can it fully determine the outer pipe wall, concealed structures, and all underwater defects. For projects requiring detection of pipeline deformation, wall thickness, or other invisible problems, other technical means should be combined according to inspection objectives.


8. Frequently Asked Selection Questions About the KT-965A

Q: Can the KT-965A inspect small DN260 pipelines?
The product's minimum applicable pipe diameter is DN260. Whether it can actually pass requires verification of the pipeline effective inner diameter, entry dimensions, sediment, and wheel set configuration. Judgment cannot be made only by nominal pipe diameter.

Q: Can the KT-965A inspect DN2000 box culverts?
The product's applicable range upper limit is DN2000. For large box culverts, wheel set and lifting configuration must be confirmed based on cross-section dimensions, bottom conditions, water accumulation, obstacles, and inspection objectives.

Q: What is the practical function of front and rear dual cameras?
The front camera is used to observe the forward direction, and the rear camera is used for reverse observation and return inspection. The two camera systems can supplement image information from different directions, making it easier for inspection personnel to check suspected defects.

Q: Is the 500 m cable a standard configuration?
No. The standard cable is 100 m, and 500 m is the maximum customizable length. The specific customization plan must be determined based on project distance and on-site layout.

Q: Can the equipment automatically generate inspection reports?
The supporting software supports one-click report generation and custom templates. Report content still needs to be reviewed in combination with inspection images, defect records, and project requirements. Software-generated reports cannot be equated with automatic completion of final engineering judgment.

Q: Can sonar and LiDAR be optionally configured?
Product documentation lists optional items including sonar, LiDAR, and laser width/distance measurement. Different optional functions correspond to different inspection objectives. Before procurement, hardware configuration, software support, and data output requirements must be confirmed.


9. KT-965A Supply, Customization, and Technical Services

Anhui Kuaitong Pipeline Cleaning Technology Co., Ltd. provides the KT-965A CCTV Pipeline Inspection Robot and related configuration services. Based on the customer's pipe diameter range, inspection distance, on-site environment, and project requirements, the company can assist in confirming wheel sets, cable length, and optional functions.

Product supply methods:

Direct supply: Equipment and standard configuration provided.

Customization: Configuration confirmed based on project inspection distance and functional requirements.

Retail: Single-unit equipment purchase and supporting accessory purchase supported.

The company provides free trial operation, demonstration videos, video tutorials, and on-site technical guidance. For customers purchasing a CCTV pipeline inspection robot for the first time, pipe diameter, pipeline length, and site photos can be provided first so that technical personnel can assist in confirming equipment configuration.


About Anhui Kuaitong Pipeline Cleaning Technology Co., Ltd.

Anhui Kuaitong Pipeline Cleaning Technology Co., Ltd., established in 2009, is a technology-oriented enterprise specializing in the R&D, manufacturing, and sales of pipeline cleaning, unclogging, and inspection equipment. The company is a National High-Tech Enterprise, a Technology-Based SME, a Training Base of the China Industrial Cleaning Association, and an Anhui Province Specialized and Sophisticated Enterprise. It has provided solutions to more than 23,000 domestic and international enterprises.

The company continuously carries out R&D of cleaning, unclogging, and inspection equipment for central air conditioning pipelines, industrial pipelines, municipal pipelines, and engineering pipelines, providing customers with product selection, equipment customization, and technical services.

Website: www.kuaitonggroup.com
Technical Consultation (Phone/WhatsApp/WeChat): +86 18226181287

This document is compiled by the technical team of Anhui Kuaitong Pipeline Cleaning Technology Co., Ltd.

PREV : Kuaitong: Pioneering Global Business Solutions

NEXT : What Equipment Is Used to Clean Blocked Corrugated Ducts in Precast Beams? KT-309 Concrete Unclogging Machine Selection

×

Get in touch